Attic truss dimensions answer one practical question: for the span and pitch your house has (or the truss you plan to order), how much space is actually up there? Once you have the numbers here, the attic size calculator turns them into floor area and volume, and the calculators hub covers the insulation and structural layers that sit inside that frame.
Truss Geometry Generator
Pick a span and pitch — the generator computes ridge height, rafter length, and the usable-room width at your target headroom, live from the same formulas the tables below use.
Method: rise = (span ÷ 2) × (pitch ÷ 12); rafter length = (span ÷ 2) × √(1 + (pitch ÷ 12)²); usable width = span − 2 × (target height ÷ (pitch ÷ 12)). Assumes a gable truss with zero heel height — add your heel (commonly 6–12" with raised-heel designs) to interior heights. For full floor area and volume from these numbers, open the attic size calculator.
Master Table: Ridge Height for 20–40 ft Trusses at 4/12–12/12
Ridge height above the wall plate for every common attic-truss span and pitch. These are exact geometric values for a simple gable profile — your truss drawing may add heel height on top. Read across for pitch, down for span:
| Span ↓ / Pitch → | 4/12 | 5/12 | 6/12 | 7/12 | 8/12 | 9/12 | 10/12 | 12/12 |
|---|---|---|---|---|---|---|---|---|
| 20 ft | 3'4" | 4'2" | 5' | 5'10" | 6'8" | 7'6" | 8'4" | 10' |
| 24 ft | 4' | 5' | 6' | 7' | 8' | 9' | 10' | 12' |
| 28 ft | 4'8" | 5'10" | 7' | 8'2" | 9'4" | 10'6" | 11'8" | 14' |
| 30 ft | 5' | 6'3" | 7'6" | 8'9" | 10' | 11'3" | 12'6" | 15' |
| 32 ft | 5'4" | 6'8" | 8' | 9'4" | 10'8" | 12' | 13'4" | 16' |
| 36 ft | 6' | 7'6" | 9' | 10'6" | 12' | 13'6" | 15' | 18' |
| 40 ft | 6'8" | 8'4" | 10' | 11'8" | 13'4" | 15' | 16'8" | 20' |
Highlighted rows (30 ft, 40 ft) are the spans most searched for attic conversions. Every cell = (span ÷ 2) × (pitch ÷ 12), computed to the inch — a self-verifying geometric dataset rather than a copied manufacturer table.
Room-in-Attic (Bonus Room) Truss Dimensions
A room-in-attic truss (sometimes "attic truss" or "bonus-room truss") is engineered with a rectangular living envelope framed into the structure: a flat ceiling zone at the ridge, square-cut vertical walls (studs between chords), and a bottom chord sized for floor loading — typically the 30–40 psf class rather than a storage rating. The room envelope is a design decision, not a pure geometric output, which is why manufacturers quote it per order.
Common envelope ranges
Published industry references put typical room-in-attic interiors at 8–10 ft wide × 7–8 ft tall on medium spans, scaling wider as span and pitch grow.
Worked reference point
A 30 ft span at 8/12 is commonly cited at 16–18 ft of room width with an 8+ ft flat ceiling (secondary references, e.g. roof pitch calculators) — the ceiling zone before knee-wall framing trims it.
The geometric method behind any manufacturer's number: the room width at a target ceiling height is exactly what the generator above computes. At 7 ft target headroom, width = span − 2 × (7 ÷ (pitch ÷ 12)). The design then subtracts framing thickness and sets the flat-cord zone — which is why quoted room widths sit a foot or two below the pure geometry.
| Span | Geometric width @ 7 ft | At 6/12 | At 8/12 | At 10/12 | At 12/12 |
|---|---|---|---|---|---|
| 20 ft | geometry → | -8' | -1' | 3'2" | 6' |
| 24 ft | geometry → | -4' | 3' | 7'2" | 10' |
| 28 ft | geometry → | 0' | 7' | 11'2" | 14' |
| 30 ft | geometry → | 2' | 9' | 13'2" | 16' |
| 32 ft | geometry → | 4' | 11' | 15'2" | 18' |
| 36 ft | geometry → | 8' | 15' | 19'2" | 22' |
| 40 ft | geometry → | 12' | 19' | 23'2" | 26' |
Data nature: pure geometry at 7 ft headroom, zero heel — a planning ceiling for what the pitch allows. Real engineered room widths run smaller after framing and design margins; use the generator for other targets.
Gambrel (Barn-Style) Attic Truss Dimensions — The Two-Slope Method
A gambrel trades one slope for two per side — a steep lower pitch that acts like a wall, and a shallow upper pitch that caps the roof. The dimension math is the same trigonometry applied twice, and it is fully deterministic once you fix three choices: span, lower pitch, and where the pitch break lands.
The gambrel's advantage is the near-standing zone, not the ridge: with a 16/12 lower slope, interior height stays above 6 ft for the first ~4.5 ft of run from each eave — versus ~2.7 ft on the straight 8/12. That difference is the entire reason barn roofs store so much more usable volume per ridge foot.
💡 Tip: Steeper lower slopes (16/12 and up) maximize the near-wall standing zone; shallower upper slopes (5/12–6/12) keep shingle installation practical. Break position controls the mix — moving it toward the eave raises the ridge fast.
❌ Don't: assume gambrel geometry from a straight-truss table. Every member, plate, and dimension differs — gambrel trusses are engineered designs with 30–50%+ more complexity than standard profiles.
Member Sizes & How to Read a Span Table
Attic trusses draw from the same dimensional-lumber family as all trusses, with one exception — the bottom chord, which carries the room:
Top chords & webs
Commonly 2×4 or 2×6 dimension lumber in typical residential spans
Bottom chord (standard)
2×4 on short spans; ceiling-load duty only in W-trusses
Bottom chord (room-in-attic)
Scales 2×6–2×8 with span; carries the 30–40 psf finished-floor class
Reading a manufacturer span table: rows are span (bearing to bearing), columns are pitch, and the load case (e.g., "room 10 psf dead + 30 psf live") governs everything — the same span carries different member sizes at different load cases. Spacing matters too: attic trusses at 16" o.c. vs 24" o.c. change member sizing and cost roughly proportionally, and wider spacing means deeper members. The stamped drawing resolves all of it; the table only gets you into the right conversation with the truss plant.
Cost anchor: attic trusses run about $200–$300 each (This Old House truss cost guide) and 30–50% more than standard Fink trusses of equivalent span — the price of the room framing and the engineering behind it.
From Truss Dimensions to Attic Space — Run the Numbers
Truss dimensions are the input; usable space is the output you actually plan around. The attic size calculator converts footprint and pitch into floor area, volume, and roof slope area, and its parametric truss table cross-checks the spans on this page. From there:
Measuring an Existing Truss Safely — In Four Steps
Most people research truss dimensions because they want to describe the trusses they already have — to a contractor, a supplier, or a permit office. Measure in place with this sequence, and the numbers you collect will reproduce everything the generator and tables above compute:
- 1Span: measure the bottom chord from inside face to inside face of the bearing walls it lands on. Never measure the exterior — siding and sheathing add inches that don't carry load.
- 2Pitch: hold a 12-inch level horizontal on the underside of a top chord and measure the rise at its far end. Rise-over-12 is your pitch — repeat on the opposite side; mismatched sides mean you have a saltbox or asymmetric design and every table here stops applying.
- 3Heel height: at the wall line, measure from the top of the wall plate to the underside of the roof sheathing along the outside face of the truss. That vertical leg is the heel — 4–6 in on older trusses, 8–12 in when a raised heel was specified for insulation depth.
- 4Member sizes: measure the depth (thickness) of the top chord, bottom chord, and one web member — 1.5 in is nominal '2x' lumber; the depth (3.5, 5.5, 7.25 in) tells you 2×4, 2×6, or 2×8.
Safety note: step only on the bottom chord or a temporary deck, keep off web members (they brace, they don't carry foot traffic), and hang a work light before climbing — measuring in the dark is how people step between trusses instead of on them.
Trusses vs. Stick Framing: Why Their Dimensions Differ
If your attic has rafters and ceiling joists instead of trusses, the tables on this page describe a different geometry than yours. A truss arrives as one triangulated assembly: its bottom chord is a tension member running wall to wall, which is exactly why standard trusses leave no walkable space — every board is structural and every web is in the way. Stick framing separates the roles: rafters carry the roof down to the walls while ceiling joists span between them in tension, and because the joists sit lower and the bays between them stay open, the same footprint at the same pitch yields noticeably more usable height and open floor. That difference is why the attic size calculator asks for the bottom-chord height as its own input — the envelope math only works when the structure type is honest.
Truss attic
Predictable exterior dimensions (span × pitch fixes the profile), zero interior flexibility, room only with engineered room-in-attic designs. No cutting, ever — one trimmed web voids the engineering.
Stick-framed attic
Same ridge-height math (rise = half-span × pitch ÷ 12), but open bays, collar-tie options, and dormer integration that trusses forbid. Modifications still need an engineer — but they are possible.
Ordering Workflow: From Table Number to Stamped Drawing
Every number on this page is an input to one conversation with a truss plant, not an order form by itself. The sequence that works: take the span, pitch, and heel measurements from the section above; add your load case (ground snow load and wind speed from your local building department); state the room envelope you want — width, height, and floor load if the room will be occupied; and send all of it to two plants for per-piece quotes. What comes back is the number that actually matters: an engineered drawing showing total height, member sizes, plate positions, and the room envelope, stamped by a licensed engineer for your jurisdiction. Treat the tables here as the vocabulary that lets you specify what you want, and the stamped drawing as the sentence that makes it real — the two never disagree on geometry, but only one of them is orderable.
Delivery, Crane & Bracing: The Dimensions That Come After the Factory
A truss's most awkward dimension is its total length, and it matters on the highway before it ever matters in your attic. A 40-foot-span truss is a 40-foot-long piece of lumber assembly that has to survive transport, turn into your street, and land on your walls. Plants deliver on flatbeds or boom trucks; anything beyond roughly 36 feet usually needs a follow car and a planned route, and lots with tight entries, low wires, or no staging area may force a crane pick at $300–$800 per day. Site access is a dimension question worth answering before you order, not after the truck arrives.
- Ground staging: each truss needs flat, level cribbing near the installation side of the house — bundles are heavy, and re-stacking a tipped bundle on soft ground is how chords get damaged before they are ever loaded.
- Temporary bracing: the first truss standing gets plumbing bracing to the ground, and each subsequent one is sheathed to its neighbor with purlins and lateral bracing per the plant's layout sheet; unbraced truss lines topple in wind surprisingly fast.
- Top-chord bearing check: confirm the bearing wall dimension matches the drawing — a truss engineered for top-chord bearing set on a bottom-chord bearing wall carries load through members never designed for it.
- Bundle weight: a typical 32-foot attic truss runs 100–150 lb per piece; plan crew size and lifting path so nobody carries a truss up a ladder solo.
Attic Truss Dimensions — Common Questions
What are the dimensions of a standard attic truss?▼
A true 'standard' dimension table does not exist because attic trusses are engineered per house — but the geometry is fixed by two inputs you already know: span and pitch. Ridge height above the bearing plate equals half the span times the pitch ratio (a 24 ft truss at 6/12 stands 6 ft at the ridge; a 40 ft truss at 8/12 stands 13'4"). Beyond overall height, what matters for a finished room is the room-in-attic variant: manufacturers commonly reserve a room 8–10 ft wide and 7–8 ft tall on medium spans, and secondary references report about 16–18 ft of usable room width on a 30 ft span at 8/12. Every actual dimension comes from the truss drawing your supplier engineers — treat published numbers as planning ranges, not orderable specs.
How tall is a 24 ft attic truss?▼
By pitch: 4/12 → 4'0", 5/12 → 5'0", 6/12 → 6'0", 7/12 → 7'0", 8/12 → 8'0", 9/12 → 9'0", 10/12 → 10'0", 12/12 → 12'0" — the arithmetic is clean because ridge height = (span ÷ 2) × (pitch ÷ 12), and half of 24 ft is exactly 12 ft. Add the heel height (the vertical distance the top chord rises above the bottom chord at the wall line — commonly 6–12 inches when raised heels are specified for insulation depth) to get total truss height off the wall plate.
How tall is a 30 ft or 40 ft attic truss?▼
A 30 ft truss rises (15 ft × pitch ÷ 12): 7'6" at 6/12, 10'0" at 8/12, 12'6" at 10/12, and 15'0" at 12/12. A 40 ft truss rises (20 ft × pitch ÷ 12): 10'0" at 6/12, 13'4" at 8/12, 16'8" at 10/12, and 20'0" at 12/12. The height question for room planning is different: what matters is how far from each eave the interior height stays above 7 ft, which the geometry generator above computes for any span–pitch pair.
How much does an attic truss cost?▼
This Old House's truss cost guide puts attic trusses at roughly $200–$300 each, and industry references note attic trusses run about 30–50% more than standard Fink trusses of the same span because of the extra lumber in the room framing. For a whole roof, attic-truss packages on a 24–28 ft span house commonly land in the low-to-mid four figures before delivery and crane time. These are national planning ranges — engineered pricing follows span, pitch, spacing, and local lumber costs, so request quotes per piece from two truss plants.
What size lumber do attic trusses use?▼
Common member sizes run 2×4 to 2×8 depending on span and the room load the design carries: top chords and web members are typically 2×4 or 2×6, while bottom chords on room-in-attic trusses scale up (2×6–2×8 on longer spans) because they carry the finished-floor load of the room they frame. There is no pick-from-a-chart answer — every member size is stamped on the engineered drawing that ships with the trusses. When you receive trusses, the drawing is the dimension record: total height, member sizes, plate positions, and the room envelope are all on it.
Do attic trusses need an engineer's stamp?▼
Yes — every attic truss ships with an engineered drawing, and most jurisdictions require the stamped drawings at permit. This is not optional paperwork: the room-in-attic design concentrates live load on the bottom chord in a way standard trusses never see, and the engineering is what makes the space legal for occupancy. If you modify anything later — cutting a web for access, notching a chord for ducts — the original engineering is void and a new engineered design is required.
What pitch do I need for a usable room in the attic?▼
For a walkable room with code-height ceilings, plan on 7/12 as the practical minimum for a clear zone of meaningful width, 8/12–10/12 for comfortable rooms, and 12/12 for the widest usable floor. The pattern is geometric: every pitch step adds usable width near the ridge. At 7 ft headroom, a 30 ft span gives a 12'6" wide center zone at 6/12 but 22'6" at 12/12 — nearly double the room from the same footprint. The generator above quantifies this for your exact span.
What is a gambrel attic truss?▼
A gambrel (barn-style) truss replaces the single straight slope with two pitches per side — a steep lower slope and a shallower upper slope — which buys near-vertical walls and a flat ceiling zone without raising the ridge. The dimension method is the same trigonometry applied twice: rise at the pitch break = segment run × lower pitch ÷ 12, and total ridge height adds the upper segment's rise. A 30 ft gambrel with a 16/12 lower slope breaking at the quarter-span and a 6/12 upper slope stands 13'9" at the ridge while giving a much wider near-standing zone than a 6/12 straight truss of the same span. Gambrels trade simplicity for geometry: more members, more plates, and engineered designs are essential.
Related Attic Structure & Space Guides
Attic Fan Dimensions: Gable, Roof-Mount & Shutter Size Chart
Real attic fan dimensions: verified Maxx Air 14″ gable fan (17.25″ cutout), Broan 356BK roof-mount (14.375″ deck hole), QuietCool AFG SMT ES-3.0, Attic Breeze GableBreeze solar variants, 30″ shutter openings, and NFA conversion.
Spray Foam in Attics — Pros, Cons & When It's Worth It
Spray foam attic insulation honestly assessed: open cell vs closed cell, pros and cons, the five known problems, sealed vs vented strategy, cost reality, and when foam is worth it.
Attic Hatch Insulation — Covers, Tents & DIY
How to insulate attic hatches, pull-down stairs, and access doors: product comparison by R-value and fit, a 1-hour DIY foam-box build, weatherstripping guide, and common mistakes.
How to Insulate an Attic — Step-by-Step Guide
How to insulate an attic step by step: air sealing, baffles, depth marking, blown-in floor installation, rafter cases, and awkward spaces (garage, knee walls, vaulted ceilings, no access) — with tools, safety, and common mistakes.
Attic Insulation Removal — When & How, Safely
When to remove old attic insulation vs insulate over it: symptom decision table, DIY vs professional removal process, PPE list, material identification chart, asbestos & vermiculite stop rules, and disposal costs.
Attic Insulation Cost — 2026 Price Guide by Sq Ft
Attic insulation cost 2026: $1–$7/sq ft installed anchors, a price matrix by material and job type, totals by attic area (400–3,000 sq ft), labor share, federal/utility incentives, and two worked payback examples.
Attic Furnace & Air Handler Dimensions: Size Charts & Clearances
Attic furnace and air handler dimensions by BTU and tonnage: verified Lennox, Goodman, and Rheem model specs, pad weights and joist loads, 30×30 working platforms, and opening reverse-checks — plus the Lennox MMDA naming trap.
Attic Renovation Cost: How Much to Finish & Convert an Attic
Attic renovation cost by line item: insulation, drywall, electrical, HVAC, flooring, dormers and bathrooms, with published $30–$60 and $100–$200 per sq ft ranges, DIY vs GC comparisons, and 53–93.5% ROI data.
Attic Storage Ideas: Safe Decking, Load Limits & What to Store
Turn attic storage into a safe plan: joist load limits (20 vs 40 psf), decking rules that keep ventilation open, truss-bay shelving vs racks, what to store and what never to store, bins, and moisture control.
Finishing an Attic: Cost, Code & Step-by-Step Conversion Guide
A 7-phase attic conversion walkthrough: feasibility checks (headroom, trusses, structure), framing to drywall sequencing, cost phases for a 1200 sq ft example, IRC R310 egress and fire code, insulation strategy, and permits.
Attic Ladder Sizes: Rough Openings & Ceiling Height Chart
Match attic ladder rough openings to ceiling heights and ceiling thicknesses. Werner, Fakro, Louisville, and Home Depot standard ladder sizes — 22.5×54, 25.5×54, 22.5×63 — plus ship ladder and custom-fit notes.
Attic Access Size: Code Minimums & Standard Dimensions
What size must an attic access opening be? IRC R807 and IBC minimums (22×30), scuttle hole vs hatch vs full door vs panel dimensions, jurisdiction code comparison, and equipment access requirements.
Blown-In Insulation Coverage Chart: Bags Needed
How many bags of blown-in insulation you need: brand-by-brand coverage per bag at R-30 to R-60, a 1200 sq ft quick-count table, roof-pitch correction, and the cutout deduction pros use.
Wall Insulation Cavity Guide: 2x4 vs 2x6 R-Values
Wall insulation by cavity depth: what R-value actually fits a 2x4 vs 2x6 wall, why compressed batts lose 30-40% of their rating, dense-pack and foam options, and the thermal bridging math.
Cellulose vs Fiberglass vs Rockwool Blown-In Compared
Cellulose vs fiberglass vs rockwool blown-in insulation compared: source materials, settled R-value, settling rates, fire ratings, moisture behavior, and installed cost — plus a 60-second material finder.
Blown-In vs Batt Insulation for Attics: Which Wins?
Blown-in vs batt insulation head-to-head in a real 1200 sq ft attic: cost, DIY feasibility, thickness, air sealing, and the new-construction-only rule that eliminates batts for 85% of retrofits.
Attic Insulation R-Value Chart: Depth by Material & Zone
Settled R-value per inch for all 13 attic insulation materials, the thickness math behind R-30 to R-60 targets, and DOE-recommended levels by climate zone — with the 15% settling overage most DIY installs miss.
Faced vs Unfaced Batt Insulation: Vapor Barrier Rules
Faced vs unfaced batt insulation by climate zone: where the vapor barrier goes (warm side, always), kraft vs poly vs smart retarders, Zone 1-3 no-barrier rules, and the four fatal installation mistakes.
DIY Blown-In Insulation vs Professional: Cost & Safety
Six-dimension comparison of DIY vs professional blown-in attic insulation: real 1200 sq ft costs ($0.64 vs $1.91/sq ft), time, quality, safety, warranty, cleanup, complete walkthroughs, and red-line conditions.
Dense-Pack vs Loose-Fill Cellulose Compared
Dense-pack cellulose (3.0-3.5 lb/cu ft) vs loose-fill (0.5-0.7 lb/cu ft). R-value per inch, settling rates, air sealing benefit, DIY feasibility, and cost comparison.
Vented vs Unvented Attic: Which Is Better?
Vented attics (cold roof, insulation on floor) vs unvented conditioned attics (warm roof, spray foam on rafters). Cost, R-value targets, ice dam risk, and climate-by-climate recommendations.
Attic Baffles & Ventilation Install Guide
Attic baffles prevent blown insulation from blocking soffit vents — the #1 cause of ice dams and hidden R-value loss. Install steps, baffle types, and vent area calculation.
Radiant Barrier for Attics: Save Energy?
Radiant barrier foil reflects roof deck radiant heat instead of absorbing it. Learn how it works, R-value equivalence by climate zone, install cost, DIY steps, and when NOT to install.